New product

Episode® 300W per Channel, 2 Channels 70 Volt Digital Power Amplifier (2 Channel - 1U Size - Audio Sense - Loop Outputs)

Episode® 300W per Channel, 2 Channels 70 Volt Digital Power Amplifier (2 Channel - 1U Size - Audio Sense - Loop Outputs)
This efficient Class-D 70V amplifier delivers gobs of power from a 2-channel design – and it only takes up a slim 1U of rack space! Outputting a whopping 300 watts per channel RMS, it’s the perfect way to add power to our integrated mixer amp and large outdoor spaces or applications that require two zones with different sources and/or volume levels. Plus this amp is chock full of installation goodies – like audio sensing turn-on, balanced and unbalanced inputs, and adjustable gain control – giving it the versatility required for today's sophisticated audio systems.


  • Digital Amplification
    Our engineers have combined advanced digital amplifier technologies with installer-friendly features to create a robust power plant built from the ground up for today's 70V system applications. Unlike analog offerings, our digital amplifiers are much more energy efficient and run up to 80% cooler. Plus, with a reduced need for heat sinks, you'll save space too with a chassis that's up to 50% smaller than traditional analog amplifiers!
  • Balanced & Unbalanced Inputs
    Most amps from the other guys force you to cut up an RCA cord to connect a standard source. Retract the razor knife and use Episode instead! This amp offers standard RCA connections for unbalanced inputs, as well as screw terminals for balanced/unbalanced inputs. So no matter what type of connection you need, you’re covered.
    Note: Inputs are independent by channel. If using a stereo source, you will need a Y-adapter to sum left and right RCAs into a single amp input.

  • Audio-Sensing and 12V Trigger Turn-On
    Three convenient turn-on modes make it easy to integrate with simple volume controls or sophisticated control systems. Audio-sense is perfect for connecting to an audio source or mixer – when the source turns off, the amplifier will gracefully go into a power-saving standby mode. The 12V trigger inputs allows you to use a mixer or control system to turn the amp on or off, or have it 'wake up' another device when the amp is activated.
    Note: The front panel power button is inoperative when the 12V Trigger or Audio Sense power modes are selected.

  • Gain Controls
    This 70V amplifier offers independent gain adjustments for each channel to normalize output volume and prevent clipping that could cause damage to the amplifier or speakers.
  • Loop Outputs
    When using a stack of amplifiers, the loop outputs are a convenient way to daisy-chain the signal to downstream components – perfect for a high power outdoor zone, for example. This eliminates the need for RCA splitters and gives a much cleaner (and faster) install.
  • Quiet Operation
    Just because this amp packs a lot of power doesn’t mean you should have to listen to it whooshing all the time. That’s why we engineered it to be fan-less – so it’s a whole lot quieter, and offers even more reliable performance.
  • Built-In ESD and Surge Protection
    Commercial environments are tough on an amplifier. Your loop of 70V speakers acts like a big antenna, so all kinds of nasty things can happen when the weather changes. That’s why we engineered this amp with high surge level protection components. During development, every connection was tortured using both an ESD and lightning simulator – all speaker outputs, audio inputs, even the power input were ESD tested with up to 15,000V and Surge tested at 2,400V. Most important, though, they each lived to tell about it.

  • Hallowed Grounds
    If you’ve ever experienced hum from your speakers or noise on your TV, odds are it was due to system grounding. This amplifier was engineered for not only the best surge protection but also with an isolated common ground for the audio circuits. The result is a great sounding, and reliable system that your customer will enjoy for years.
  • Installation Flexibility
    A slim 1U chassis takes up less space when stacked on a shelf or installed in a rack. Included rack ears and amplifier feet give you the flexibility to install it where you need.

Product Package Includes:
(1) Amplifier
(1) Detachable IEC Power Cable
(4) Removable Rack Feet and Screws
(2) Rack Mounting Ears and Screws
(1) 5mm 6-pin Screw Terminal
(1) 5mm 4-pin Screw Terminal
(1) Installation Manual